New Directions
As we indicated last week, our promised new releases took us out of the realm of board game pieces. We ventured into two entirely new areas: jewelry and drink coasters! Read more about them below, but first I’m going to tell you about fixing the heat creep blockage we also mentioned last week.
The Blockage Got Worse
When I wrote about it last week we had a workaround for temporarily dealing with the blockage. But then the problem got worse. While we could still get some filament through, it wasn’t enough. We were facing pretty bad under-extrusion problems, where not enough filament was getting through the nozzle, leaving the print with gaps, thin layers, and poor adhesion. We ended up needing to stop all printing for a day and a half.
Digging Into the Problem
Then our supplies arrived and I began disassembling the printer’s hot end (what you might think of as the print head on a traditional printer). Here you see it opened up and laid out for inspection. Even to get to this point I had to disengage it from the X-axis drive belt, and remove two of the wheels and the print cooling fan. The problem is somewhere between where the Bowden tube (the white tube at the top) enters, and the nozzle (the pointy metal bit at the lower left of the assembly).
Isolating the Problem Area
Next I removed the back panel (with the remaining wheel) from the heat dissipation block (the central black thing with the fins for air cooling), and unscrewed the Bowden tube connector. You can also see a glob of melted and burnt filament plastic on top of the rectangular heating block that the nozzle is screwed into. But to go any further I had to turn on the printer and heat it up. Everything was fused together by solidified printing plastic, and it had to be softened before I could do anything else.
Smokin’ Hot! Literally!
Once it was heated I was able to pull that piece of plastic off the top of the heating block.
I also removed the nozzle and confirmed that the blockage was higher than that.
The Bowden tube itself was really stuck hard in there! I had to hold the heat dissipation block with pliers and pull hard on the tube to get it out, all while being very aware that I was dealing with parts heated to 235ºC (455ºF).
When it finally came out, it was blackened and smoking! Unfortunately the smoke dissipated before I could snap a pic of it, but here you can see the blackened end of the Bowden tube. It smelled faintly sweet, which makes sense I guess considering PLA is made from corn starch.
The Solution
While the root cause of the problem is still just an educated guess (as I speculated last week, I think it came from operating the printer very hot for the metallic filament), the immediate problem was clear. The end of the Bowden tube was completely blocked with burned filament. Since I had already purchased a new one, I just had to cut it to length and install it. I was grateful to not have to remove the heat break (the metal connection between the heater block and the heat dissipation block), though I did clean out the inside of it with a pipe cleaner. (A real pipe cleaner, not the colored ones that kids use for crafts as that would have melted.)
Here it is with the new Bowden tube installed (this one is blue) and the nozzle back in place.
As I put it all back together, I also cleaned it up and tightened some screws that had become slightly loosened.
Better Than Ever!
Here it is printing some heart trains from our Valentine Ticket to Ride set. They came out beautifully and the printer is working better than ever! I love our new Capricorn Bowden tube! My research showed it was the best brand on the market, and I have to agree.
Valentine Earrings
With that major problem out of the way, we could move ahead with our releases for the week, starting with some Valentine earrings! Our first jewelry offering looks stunning! They come in two styles:
and Cascade Heart.
There are six unique pairs in each style, including several featuring our new metallic filament. Follow the links to our Etsy shop to see them all.
Catan Coasters – With Puns!
We also launched our first set of drink coasters.
They’re themed to match the five resources from Settlers of Catan and would be perfect to use when hosting game night!
Each hex-shaped coaster is colored to match a resource, has cute little icons around the edges, and features a related pun. The set also comes with a tray to store or display them!
Next Up – A Whole New Game!
The project we’re currently working on gets back to game pieces, but they’re for a game we haven’t worked on before. Whether or not you’re a fan of the game, we guarantee it’s one you’ve heard of! Come back in a week to see if we’ve launched it!